Plus Two Electronics Practical Viva Questions and Answers

Plus Two Electronics Practical Viva Questions and Answers

Plus Two Electronics Practical Viva Questions and Answers: In this article, we will provide some of the most asked practical viva questions and answers asked in the Plus Two Electronics Practical exam each year. We have compiled this list from viva questions from analysis of previous practical exams and collected these Plus Two Electronics Practical Viva Questions and Answers for students preparing for upcoming Electronics practical exams.

Plus Two Electronics Practical Viva Questions and Answers

Plus Two Electronics Practical Viva Exam. A necessary evil. Most students break out in a cold sweat at the mere thought. How do I prepare? What are they going to ask me? What should I ask them? Those are just a few of the questions that run through the mind of the average student.

Board	SCERT, Kerala
Class	Plus Two
Subject	Electronics
Exam	Practical
Study Materials	Viva Q&A
Provider	Hsslive.co.in
Plus Two All Subject Practical Viva Q&A	Click Here

How to get Plus Two Electronics Practical Viva Questions?

1. Visit our website of hsslive.co.in
2. Search for Plus Two Practical Viva Questions and Answers
3. Now look for Plus Two Electronics Practical Viva Questions and Answers.
4. Bookmark this page for preparing for Plus Two Electronics Practical Viva Exam.

Plus Two Electronics Practical Viva Questions & Answers

We have listed below the list of most asked plus two Electronics practical viva questions along with answers of each below:

1. What is an ideal voltage source?
Answer: A device with zero internal resistance.

2. What is an ideal current source?
Answer: A device with infinite internal resistance.

3. What is a practical voltage source?
Answer: A device with small internal resistance.

4. What is a practical current source?
Answer: A device with large internal resistance.

5. The voltage out of an ideal voltage source is
A. Zero
B. Constant
C. Load resistance dependent
D. Internal resistance dependent
Answer: B

6. The current out of an ideal current source is
A. Zero
B. Constant
C. Load resistance dependent
D. Internal resistance dependent
Answer: B

7. The path between two points along which an electrical current can be carried is called
A. A network
B. A relay
C. A circuit
D. A loop
Answer: C

8. The formula for current as per Ohm’s Law is
A. Voltage / Resistance
B. Resistance * Voltage
C. Voltage + Resistance
D. Resistance / Voltage
Answer: A

9. The unit of electrical resistance is
A. Volt
B. Amp
C. Ohm
D. Coulomb
Answer: C

10. In a constant voltage DC circuit, when the resistance increases, the current will
A. Decrease
B. Stop
C. Increase
D. Remains constant
Answer: A

Basic Semiconductor Theory Questions

1. Number of valence electrons in a silicon atom are
A. 1
B. 4
C. 8
D. 16
Answer: B

2. The most commonly used semiconductor element is
A. Silicon
B. Germanium
C. Gallium
D. Carbon
Answer: A

3. Copper is a
A. Insulator
B. Conductor
C. Semiconductor
D. Super Conductor
Answer: B

4. Number of protons in the nucleus of a silicon atom are
A. 4
B. 14
C. 29
D. 32
Answer: B

5. The valence electron of a conductor are also called as
A. Bound electron
B. Free electron
C. Nucleus
D. Proton
Answer: B

6. An intrinsic semiconductor at room temperature has
A. A few free electrons and holes
B. Many holes
C. Many free electrons
D. No holes
Answer: A

7. At room temperature, an intrinsic semiconductor has some holes in it due to
A. Doping
B. Free electrons
C. Thermal energy
D. Valence electrons
Answer: C

8. The number of holes in an intrinsic semiconductor is
A. Equal to number of free electrons
B. Greater than number of free electrons
C. Less than number of free electrons
D. None of the above
Answer: A

9. Holes act as
A. Atoms
B. Crystals
C. Negative charges
D. Positive charges
Answer: D

10. Pick the odd one in the group
A. Conductor
B. Semiconductor
C. Four valence electrons
D. Crystal structure
Answer: A

11. To produce P-type semiconductors, you need to add
A. Trivalent impurity
B. Carbon
C. Pentavalent impurity
D. Silicon
Answer: A

12. Electrons are the minority carriers in
A. Extrinsic Semiconductors
B. p-type Semiconductors
C. Intrinsic Semiconductors
D. n-type Semiconductors
Answer: D

13. A p-type semiconductor contains
A. Holes and Negative ions
B. Holes and Positive ions
C. Holes and Pentavalent atoms
D. Holes and Donor atoms
Answer: A

14. How many electrons does pentavalent atoms have?
A. 1
B. 3
C. 4
D. 5
Answer: D

15. Negative ions are
A. Atoms that obtained a proton
B. Atoms that lost a proton
C. Atoms that obtained an electron
D. Atoms that lost an electron
Answer: C

16. What is the result of Ionization in PN Junction on either side of potential barrier?
A. Barrier Voltage
B. Junction
C. Depletion Region
D. Forward Voltage
Answer: C

17. The cause of Depletion Region is __________
A. Diffusion
B. Ions
C. Doping
D. Forward Voltage
Answer: A

18. Which of the following is a Semiconductor?
A. Argon
B. Carbon
C. Mica
D. Ceramic
Answer: B

19. Doping material among the following is
A. n-type Semiconductor
B. Majority Carriers
C. Extrinsic Semiconductor Material
D. Pentavalent Material
Answer: D

20. We can easily activate minority carriers using
A. Forward Voltage
B. Doping
C. Heat
D. Pressure
Answer: C

Basic Semiconductor Diode Questions

1. Depletion layer is caused by
A. Doping
B. Recombination
C. Barrier potential
D. Ions
Answer: B

2. The reverse current in a diode is usually
A. Very small
B. Very large
C. Zero
D. In the breakdown region
Answer: A

3. Avalanche in Diode occurs at
A. Barrier potential
B. Depletion layer
C. Knee voltage
D. Breakdown voltage
Answer: D

4. The potential barrier of a silicon diode is
A. 0.3 V
B. 0.7 V
C. 1 V
D. 5V
Answer: B

5. The reverse saturation current in a Silicon Diode is _____ than that of Germanium Diode
A. Equal
B. Higher
C. Lower
D. Depends on temperature
Answer: C

6. A Diode is a
A. Bilateral Device
B. Nonlinear Device
C. Linear Device
D. Unipolar Device
Answer: C

7. The diode current is large for which condition
A. Forward Bias
B. Inverse Bias
C. Poor Bias
D. Reverse Bias
Answer: A

8. The output voltage signal of a bridge rectifier is
A. Half-wave
B. Full-wave
C. Bridge-rectified signal
D. Sine wave
Answer: B

9. If the maximum DC current rating of diodes in Bridge Rectifier is 1A, what is the maximum DC load current?
A. 1A
B. 2A
C. 4A
D. 8A
Answer: B

10. Voltage multipliers produce
A. Low voltage and low current
B. Low voltage and high current
C. High voltage and low current
D. High voltage and high current
Answer: C

11. What is a Clipper?
Answer: A circuit that removes a part (positive or negative) of a waveform so that it doesn’t exceed a certain voltage level.

12. What is a Clamper?
Answer: A circuit that adds a DC voltage (positive or negative) to a wave.

13. Zener diode can be described as
A. A rectifier diode.
B. A device with constant – voltage.
C. A device with constant – current.
D. A device that works in the forward region.
Answer: B

14. If the Zener Diode is connected in wrong polarity, the voltage across the load is
A. 0.7 V
B. 10 V
C. 14 V
D. 18 V
Answer: A

15. Since diodes allow flow of current in only one direction, they can be used for
A. Current Limiting
B. Reverse Polarity Protection 
C. Storing Charge
D. Voltage Regulation
Answer: B

16. When you test a good diode with a multimeter, it shows 
A. Low resistance when forward biased or reverse biased
B. High resistance when forward biased or reverse biased
C. High resistance when forward biased and Low resistance when reverse biased
D. Low resistance when forward biased and High resistance when reverse biased
Answer: D

17. When does current flow in a PN junction?
A. When both p-type and n-type elements are at same potential
B. When there is no potential at either p-type or n-type elements
C. When p-type element is at more positive potential than n-type
D. When n-type element is at more positive potential than n-type
Answer: C

18. Clamping Circuits are generally used in
A. TV Transmitters and Receivers
B. FM Transmitters
C. Signal Generators (Square, Trapezoid, etc.)
D. All the above
Answer: D

19. Units of measurement for forward bias and reverse current of a diode are
A. µA and µA
B. mA and µA
C. µA and mA
D. mA and mA
Answer: B

20. What graphical method is used for modelling Diode Characteristics
A. Exponential Method 
B. Small Signal Approximation
C. Iteration Method
D. Constant Voltage Drop Method
Answer: A

Basic Transistor Questions

1. Number of PN Junctions in a Transistor
A. One
B. Two
C. Three
D. Four
Answer: B

2. The doping concentration of Base in NPN Transistor is
A. Lightly Doped
B. Moderately Doped
C. Heavily Doped
D. Not Doped
Answer: A

3. The Base – Emitter Diode (Base – Emitter Junction) in an NPN Transistor is
A. Doesn’t conduct
B. Forward Biased
C. Reverse Biased
D. Operates in breakdown region
Answer: B

4. The size comparison between Base, Emitter and Collector is
A. Base > Collector > Emitter
B. Emitter > Collector > Base
C. Collector > Emitter > Base
D. All are equal
Answer: C

5. The Base – Collector Diode (Base Collector Junction) is usually
A. Reverse Biased
B. Forward Biased
C. Breakdown Region
D. No Conduction
Answer: A

6. The DC Current Gain of a Transistor is
A. Ratio of Emitter Current to Collector Current
B. Ratio of Base Current to Emitter Current
C. Ratio of Collector Current to Base Current
D. Ratio of Base Current to Collector Current
Answer: C

7. If base current is 100µA and current gain is 100, then collector current is
A. 1A
B. 10A
C. 1mA
D. 10mA
Answer: D

8. The majority carriers in NPN and PNP Transistors are
A. Holes and Electrons
B. Electrons and Holes
C. Acceptor Ions and Donor Ions
D. None
Answer: B

9. A Transistor acts as a
A. Voltage Source and a Current Source
B. Current Source and a Resistor
C. Diode and Current Source
D. Diode and Power Supply
Answer: C

10. The relation between Base Current IB, Emitter Current IE and Collector Current IC is
A. IE = IB + IC
B. IB = IC + IE
C. IE = IB – IC
D. IC = IB + IE
Answer: A

11. The total power dissipated by a transistor is a product of collector current and
A. Supply Voltage
B. 0.7V
C. Collector – Emitter Voltage
D. Base – Emitter Voltage
Answer: C

12. The input impedance of Common Emitter Configuration is
A. Low
B. High
C. Zero
D. Very High
Answer: A

13. The output impedance of Common Emitter Configuration is
A. Low
B. Very Low
C. High
D. Zero
Answer: C

14. Two types of Bipolar Junction Transistors (BJTs) are 
A. nnn and ppp
B. npn and pnp
C. pnn and npp
D. nnp and ppn
Answer: B

15. What are the common faults in BJT? 
A. Internal Short
B. Open Bias Resistor 
C. External Open and
D. nnp and ppn
Answer: B

16. The usual operating region of Transistors in Digital Circuits is 
A. Active Region
B. Linear Region
C. Breakdown Region
D. Cutoff and Saturation Region
Answer: D

17. Another name for Emitter Follower Configuration is 
A. Common Base Amplifier
B. Common Emitter Amplifier
C. Common Collector Amplifier 
D. Darlington Pair
Answer: C

18. BJT is a _________ and a FET is ________ 
A. Bipolar and Unipolar
B. Bipolar and Bipolar
C. Unipolar and Unipolar
D. Unipolar and Bipolar
Answer: A

19. The current gain in Common Base configuration (α) is 
A. Ratio of Base Current to Emitter Current (IB/IE)
B. Ratio of Collector Current to Emitter Current (IC/IE)
C. Ratio of Collector Current to Base Current (IC/IB)
D. None
Answer: B

20. Relation between α and ß is 
A. α = ß / (ß + 1) 
B. ß = α / (1 – α)
C. α = ß * (ß + 1)
D. α = ß / (ß – 1)
Answer: Both A and B

Plus Two All Subjects Practical Viva Questions & Answers

• Plus Two Practical Viva Questions and Answer
• Plus Two Physics Practical Viva Questions and Answer
• Plus Two Chemistry Practical Viva Questions and Answer
• Plus Two Zoology Practical Viva Questions and Answer
• Plus Two Botany Practical Viva Questions and Answer
• Plus Two Computer Science Practical Viva Questions and Answer
• Plus Two Computer Application Humanities Practical Viva Questions and Answer
• Plus Two Computer Application Commerce Practical Viva Questions and Answer
• Plus Two Computerised Accounting Commerce Practical Viva Questions and Answer
• Plus Two Geography Practical Viva Questions and Answer
• Plus Two Geology Practical Viva Questions and Answer
• Plus Two Mathematics Practical Viva Questions and Answer
• Plus Two Communicative English Practical Viva Questions and Answer
• Plus Two Electronics Practical Viva Questions and Answer
• Plus Two Gandhian Studies Practical Viva Questions and Answer
• Plus Two Home Science Practical Viva Questions and Answer
• Plus Two Journalism Practical Viva Questions and Answer
• Plus Two Psychology Practical Viva Questions and Answer
• Plus Two Statistics Practical Viva Questions and Answer
• Plus Two Accountancy Practical Viva Questions and Answer

Importance of Plus Two Electronics Practical Viva Questions & Answers

All students should know the plus two Electronics practical viva questions to enhance their preparation in the right direction for the examinations. It will help the students to get an answer and help them to manage their time during the exam effectively.

Plus Two All Subjects Practical Records

• Plus Two Physics Practical Records
• Plus Two Electronics Practical Records
• Plus Two Zoology Practical Records
• Plus Two Botany Practical Records
• Plus Two Computer Science Practical Records
• Plus Two Computer Application Humanities Practical Records
• Plus Two Computer Application Commerce Practical Records
• Plus Two Computerised Accounting Commerce Practical Records
• Plus Two Geography Practical Records
• Plus Two Geology Practical Records
• Plus Two Mathematics Practical Records
• Plus Two Communicative English Practical Records
• Plus Two Electronics Practical Records
• Plus Two Gandhian Studies Practical Records
• Plus Two Home Science Practical Records
• Plus Two Journalism Practical Records
• Plus Two Psychology Practical Records
• Plus Two Statistics Practical Records